Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: Bullets

  1. #1
    7tharkinf is offline
    Team:
    Visitor (non-N-SSA Member)
    Member
    N/A
    Join Date
    Apr 2013
    Posts
    39
    Region:
    Visitor

    Bullets

    I was just wondering what was the best premade bullets on the market I have an Enfield armi sport and I'm looking for a .575 conical old style minie preferred but up to hearing any suggestions.

  2. #2
    Hickok's Avatar
    Hickok is offline
    Team:
    Visitor (non-N-SSA Member)
    Member
    NA
    Join Date
    May 2013
    Location
    Occupied Western Virginia,...Thomas WV
    Posts
    105
    Region:
    Visitor
    Pat Kaboskey <cwbulletman@aol.com>

    You may want to find the bore diameter of your barrel as they can vary. I have an Armisport 1853 Enfield and it has a .581" bore diameter. Recommended procedure is to shoot a Minie that is .001" to .002" smaller than bore diameter for best accuracy. Therefore this rifle musket should be best loaded with a .580" or .579" sized Minie.

    Pat Kaboskey can provide bullets of various diameters.
    Relatives; Isaac W. Shafer 33rd Va. Inf. Lost right arm at Antietam
    Obed T. Shafer 33rd Va. Inf. wounded at Battle of Monocacy Md.
    David H. Shafer 6th. WV Cav. captured Battle of New Creek WV
    died POW Richmond Va.

  3. #3
    7tharkinf is offline
    Team:
    Visitor (non-N-SSA Member)
    Member
    N/A
    Join Date
    Apr 2013
    Posts
    39
    Region:
    Visitor
    Well then that raises another question where can I get a reasonable priced bore gauge
    ?

  4. #4
    Hickok's Avatar
    Hickok is offline
    Team:
    Visitor (non-N-SSA Member)
    Member
    NA
    Join Date
    May 2013
    Location
    Occupied Western Virginia,...Thomas WV
    Posts
    105
    Region:
    Visitor
    http://www.amazon.com/gp/product/B00...?ie=UTF8&psc=1



    Try a .581", a .579" and maybe a .577" plug gauge. They aren't very expensive. Seems alot of repro muskets run a little on the large side as to bore diameter. I found plug gauges were the easiest and most accurate way to check.
    Relatives; Isaac W. Shafer 33rd Va. Inf. Lost right arm at Antietam
    Obed T. Shafer 33rd Va. Inf. wounded at Battle of Monocacy Md.
    David H. Shafer 6th. WV Cav. captured Battle of New Creek WV
    died POW Richmond Va.

  5. #5
    Join Date
    Jan 2009
    Location
    Huntsville
    Posts
    3,911
    Region:
    Deep South - Georgia, Louisiana, Tennessee, Mississippi and Texas
    Hickok
    http://www.amazon.com/gp/product/B00...?ie=UTF8&psc=1



    Try a .581", a .579" and maybe a .577" plug gauge. They aren't very expensive. Seems alot of repro muskets run a little on the large side as to bore diameter. I found plug gauges were the easiest and most accurate way to check.
    HOLY COW WHERE HAVE YOU BEEN MY WHOLE LIFE??????

    I looked up these kinds of things on Grainger and such and they were like $70!

    Steve

  6. #6
    Join Date
    Jan 2009
    Location
    Huntsville
    Posts
    3,911
    Region:
    Deep South - Georgia, Louisiana, Tennessee, Mississippi and Texas
    I was just wondering what was the best premade bullets on the market I have an Enfield armi sport and I'm looking for a .575 conical old style minie preferred but up to hearing any suggestions.
    I have great success shooting the RCBS-Hogdgon in my Enfield with a Whitacre barrel with 1:72 twist.

    It also shoots very well with the RCBS-500M.

    As was noted, I size mine to the nearest .001" that will fit.

    Steve

  7. #7
    Hickok's Avatar
    Hickok is offline
    Team:
    Visitor (non-N-SSA Member)
    Member
    NA
    Join Date
    May 2013
    Location
    Occupied Western Virginia,...Thomas WV
    Posts
    105
    Region:
    Visitor
    You want to check just the bore diameter at the muzzle, don't drop the plug gauge down the barrel.
    Relatives; Isaac W. Shafer 33rd Va. Inf. Lost right arm at Antietam
    Obed T. Shafer 33rd Va. Inf. wounded at Battle of Monocacy Md.
    David H. Shafer 6th. WV Cav. captured Battle of New Creek WV
    died POW Richmond Va.

  8. #8
    Hickok's Avatar
    Hickok is offline
    Team:
    Visitor (non-N-SSA Member)
    Member
    NA
    Join Date
    May 2013
    Location
    Occupied Western Virginia,...Thomas WV
    Posts
    105
    Region:
    Visitor
    Steve, I tryed the various other methods of determining true bore diameter, but never got a positive reading I was sure of. With the plug gauges I found my barrel was slightly "tighter" than I thought!
    Relatives; Isaac W. Shafer 33rd Va. Inf. Lost right arm at Antietam
    Obed T. Shafer 33rd Va. Inf. wounded at Battle of Monocacy Md.
    David H. Shafer 6th. WV Cav. captured Battle of New Creek WV
    died POW Richmond Va.

  9. #9
    Ron/The Old Reb Guest
    Here is how I do it without a plug gage. Take a Minnie that is larger then the bore. Drill a small hole in the base. Then screw in a sheet metal screw. Tap the Mine into the muzzle about half way. Clamp the screw in a vice get a good hold on the barrel and pull it out. Measure across the grooves with a set of vernier's. You want a Minnie one to two thousand's smaller than the reading you get.

  10. #10
    Join Date
    Dec 2004
    Location
    Sherman's Kitchen, GA
    Posts
    980
    Region:
    Deep South - Georgia, Louisiana, Tennessee, Mississippi and Texas

    Bullets

    Quote Originally Posted by 7tharkinf View Post
    I was just wondering what was the best premade bullets on the market I have an Enfield armi sport and I'm looking for a .575 conical old style minie preferred but up to hearing any suggestions.
    Cannot say just who offers the best premade bullets on the market but do be careful when you buy them. Another gent here, Southron Sr., attended the first Nathan Bedford Forrest Skirmish in 1978 when it was held at a city park in Union City, TN, and flew in from Winchester so couldn't bring any ammo with him. So he bought some premade bullets from Dixie Gun Works, along with a .571 sizer and one of Dixie's so-called "indestructable" bullet starters to push the bullets through the sizer. I don't rightly recall just how many bullets he had "sized" or rather beat them through the sizer, but the stress test he put that bullet starter through... it finally shattered into a gazillion pieces! So it might be good to have more than one size sizing die because if you are attempting to size a .580 thru a .571 sizer, the bullet length may tend to "grow" (enlongate) on you. I have sizers in 1/1000th increments from .577 down to .573 just to insure the bullet doesn't distort when sizing.
    First Cousin (7 times removed) to Brigadier General Stand Watie (1806-1871), CSA
    1st Cherokee Mounted Rifles | Principal Chief of the Cherokee Nation 1862-66

Similar Threads

  1. WTB Bullets
    By Grenadier in forum Wanted/For Sale Items
    Replies: 3
    Last Post: 07-27-2011, 05:06 PM
  2. .38-55 bullets
    By dml1296 in forum Wanted/For Sale Items
    Replies: 0
    Last Post: 03-21-2011, 03:44 AM
  3. 44 and 36 Conical Bullets
    By The Wizard in forum Small Arms
    Replies: 8
    Last Post: 05-08-2010, 03:10 PM
  4. How were bullets made?
    By in forum Small Arms
    Replies: 6
    Last Post: 02-03-2010, 07:19 PM
  5. wilkinson bullets still looking
    By Sam Sellaro, 12403 in forum Wanted/For Sale Items
    Replies: 2
    Last Post: 11-02-2009, 09:54 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •