Results 1 to 9 of 9

Thread: SS Pistol Woes

  1. #1
    sjezior is offline
    Team:
    Battery H, First Regt. Ill. Vol. Light Artillery
    Member
    11949
    Join Date
    Oct 2007
    Posts
    28
    Region:
    Western - Illinois and Wisconsin

    SS Pistol Woes

    Anyone else have problems with their Single Shot Harpers Ferry pistol not firing consistently?

    Seems I'm not getting powder down to the cone after firing a few shots. Could powder get stuck on fouling or for whatever reason not get down to where the cap can set it off? To get the ball out, I've removed the clean out screw and poured powder there and it works (obviously not a solution for team events).

    Could CCI caps not have enough spark to reach the main charge if the cone isn't full of powder?

    I upped the charge to 35 from 20 grains and it works a bit better but not consistent. I tried both 2f and 3f.

    I'm wondering if drilling out the nipple hole would help get the spark further down the chamber.

    Appreciate any thoughts on fixing this!
    Stan Jezior
    Battery H 1st Ill Lt Arty

  2. #2
    Harry Gaul's Avatar
    Harry Gaul is offline
    Team:
    Forney's Battalion, USMC
    Member
    3626
    Join Date
    Jul 2006
    Location
    East Petersburg, PA
    Posts
    722
    Region:
    Middle Atlantic - New York, Pennsylvania and New Jersey

    My experince with Italian made firearms.

    This problem sounds like the hole in the breech area from the breech to the cone is above the threading of the cone. You might want to try to drill out the hole in the breech and see if that helps. Check the opening through the clean out screw first with a probe. I helped a reenactor who had an 1861 musket. Once I lowered the hole from the breech to the bolster, the musket fired beautifully with blanks. Go slow and you should find the sweet spot.

    Harry in pa.
    Forney's
    03626v

  3. #3
    Join Date
    Aug 2012
    Location
    Virginia Beach, VA
    Posts
    97
    Region:
    Tidewater - Virginia and North Carolina
    Try less powder, more is not always better.
    Rick G. Cameron Jr.
    13082

  4. #4
    Join Date
    Feb 2006
    Location
    Williamsburg, VA
    Posts
    318
    Region:
    Tidewater - Virginia and North Carolina
    Switch to a Musket cap nipple. Much hotter.
    Gary B
    Gary Bowling, Commander
    Nansemond Guards, 6th VA Co. E, CSA

    "Rear sights are STILL overrated"

  5. #5
    Wrekreation is offline
    Team:
    49th Virginia Infantry
    Member
    2016 13540 110-pt
    Join Date
    Jun 2016
    Posts
    33
    Region:
    Central Virginia - Virginia and North Carolina

    Harper's ferry pistol

    The SS Harpers Ferry Pistol has a semi-patented breech. In my experience it requires some intense cleaning. Carl Kruger and I have been working with Tom Krone to see if we can perfect a small scraper to fit down into the breech to clean it out. It will quickly foul with 25 rounds of a low powder load - I use 12 gn of 3F. I've included a line drawing provided by Mr. Pedersoli that shows the breech. Name:  Screenshot 2024-09-11 at 8.00.29 AM.jpg
Views: 285
Size:  11.0 KB

  6. #6
    Join Date
    Jan 2009
    Location
    Huntsville
    Posts
    3,813
    Region:
    Deep South - Georgia, Louisiana, Tennessee, Mississippi and Texas
    I wish the manufacturers would stop putting patent breeches on guns that didn't have them.

    Looking at you Pedersoli Lorenz.

    Steve
    Steve Sheldon
    Commander
    4th Louisiana Delta Rifles
    NRA Certified Muzzleloading Instructor

  7. #7
    Join Date
    Mar 2020
    Location
    Heart of Dixie
    Posts
    71
    Region:
    Deep South - Georgia, Louisiana, Tennessee, Mississippi and Texas
    I've had similar issues with the Pedersoli Harpers Ferry SSP. Even when the flash channel and everything else is in my opinion very clean, it requires a RWS 1075+ cap to be reliable. CCI Magnum 11's work ok too. Remington and Standard non-magnum CCI caps seem to have a higher misfire rate.

    For cleaning the breech, I flattened the end of a piece of 1/4" brass tubing to make a "scraper". Follow with cleaning the sub-chamber using a 32 cal bore mop. The first time trying to clean the patent breech, I found that my drum was threaded in farther than I think it should be. There was no chance of getting a scraper of a decent size inside. I ground off somewhere around 1/16" from the threaded side and can now clean without removing the drum.

  8. #8
    Join Date
    Jan 2009
    Location
    Huntsville
    Posts
    3,813
    Region:
    Deep South - Georgia, Louisiana, Tennessee, Mississippi and Texas
    Likewise with my Pedersoli Pennsylvania rifle, I believe, the touch hole liner was threaded into the patent beech region, making effective cleaning of the patent breech difficult.

    Steve
    Steve Sheldon
    Commander
    4th Louisiana Delta Rifles
    NRA Certified Muzzleloading Instructor

  9. #9
    sjezior is offline
    Team:
    Battery H, First Regt. Ill. Vol. Light Artillery
    Member
    11949
    Join Date
    Oct 2007
    Posts
    28
    Region:
    Western - Illinois and Wisconsin
    I found that using the ram rod after pouring in the powder load before the ball will get powder into the patent breech. No problems with the regular CCI caps then. It's an extra step but works.
    Stan Jezior
    Battery H 1st Ill Lt Arty

Similar Threads

  1. 1855 3 band woes
    By Michael T. in forum Shooting Techs, Tips, & Tricks
    Replies: 9
    Last Post: 04-20-2023, 09:03 PM
  2. 1855 3 band woes
    By Michael T. in forum Small Arms
    Replies: 14
    Last Post: 10-28-2022, 09:34 AM
  3. Pistol FS
    By Stefan in forum Wanted/For Sale Items
    Replies: 0
    Last Post: 06-25-2019, 04:56 PM
  4. 56-56 Spencer woes
    By Dave Fox in forum Shooting Techs, Tips, & Tricks
    Replies: 9
    Last Post: 04-10-2011, 12:46 PM
  5. Burnside woes
    By Dave Fox in forum Small Arms
    Replies: 7
    Last Post: 03-03-2010, 09:32 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •