Results 1 to 4 of 4

Thread: Attaching sight

  1. #1
    tucten is offline
    Team:
    27th North Carolina State Troops
    Member
    NA
    Join Date
    Aug 2016
    Posts
    21
    Region:
    Carolina - North Carolina and South Carolina

    Attaching sight

    I?ve struggled with this far too long. How do I attach a brass sight to my Smith sight base. TIA

  2. #2
    Join Date
    Jan 2008
    Location
    Eastern North Carolina
    Posts
    297
    Region:
    Tidewater - Virginia and North Carolina

    Attaching sight

    Hi depending on your skill level there are several methods....
    prior to removing the sight base "index" the location on the off side with a punch so you put the base back in the original position.
    1. Remove sight and place in a vice
    2. clean and flux the sigh base with solder flux
    3. "Tin" the slot with a minimum amount of solder
    4. Flux the brass insert and tin the insert with solder
    5. heat the base with torch and insert blade when the solder liquifies
    6. wipe excess solder off , let cool and replace sight

    or
    1. Remove sight and place in a vice
    2. place blade in slot in base
    3. carefully drill a hole thru the base and base in the front and back of base
    4. insert a small pin in hole, trim ends to be flush
    5. Reinsert base in gun

    it sounds harder than it really is
    mike

  3. #3
    Lou Lou Lou is offline
    Team:
    Tammany Regiment, 42nd New York
    Member
    4869
    Join Date
    May 2004
    Location
    Lung Island, New Yawk
    Posts
    1,965
    Region:
    New England - New York, Connecticut, New Jersey and Massachusetts
    Don?t understand exactly what you want to do.
    the front sight base will take a replacement blade easy peasy.
    can you explain what you want to do?
    Lou Lou Lou Ruggiero
    Tammany Regt-42nd NYVI

  4. #4
    Join Date
    Jan 2009
    Location
    Huntsville
    Posts
    3,733
    Region:
    Deep South - Georgia, Louisiana, Tennessee, Mississippi and Texas
    First, drive the old blade out of the site. You'll want to carefully secure the sight in a vice, and then use a small punch to drive it out of its slot. You can fashion a small punch out of a small nail.

    Then, you'll want to fashion a new blade out of a piece of brass, or German silver, or whatever. Make it taller than you think you need. Start out with a piece that is slightly thicker than you need.

    Use some calipers to measure the width of your original blade. File the new blade thickness until it is just a tiny bit thicker than the original blade. You want an interference fit when driving it home. You don't want it massively oversize or you can split the sight base in half or break off the wings. Remember, if you screw up the blade it is not a big deal just file out a new one. Slow, steady, careful fitting wins the race. Remember you just want a slight interference fit. You're not trying to drive a wedge in a log. A few thousandths of an inch oversize will do.

    You'll notice that the bottom of the slot is very slightly wider than the top. This traps the blade once it is in place. Try and match this shape as you file your new blade.

    You'll want to file a chamfer on the front of the blade. This is a "lead in" so that when you tap the new blade into the slot, it starts easily. In other words, make the front edge of the blade a bit narrower than the slot so it starts into the slot easily. Carefully tap it into place with a small hammer. If you do it right, you won't need any solder. However, if you like, you can "tin" the blade before you drive it in place, flux the groove, drive the blade in, and heat the base until the solder melts. However, the blade may shift in its slot since the solder was making up part of the interference fit. I've replaced the blade on 3 Smiths and did not use solder on any of them.

    Once the blade is in place, you can file it to a final shape. You can clean it up fore and aft so it is flush with the sight base. File the height to be close, but taller than you need. If your blade is too short you'll be back in the shop making another one.

    If you have not yet done a load workup, don't do any sight work until you have achieved your optimal group size. Only then work on the sight. You can then file the blade down to get the point of impact you desire for your point of aim. After that you can finish dressing the blade to the final shape you desire, following the original configuration of the original sight blade as your guide.





    You can also buy complete sights from S&S Firearms:
    https://www.ssfirearms.com/proddetail.asp?prod=SC36

    S&S also sells front blades in different thicknesses:
    https://www.ssfirearms.com/proddetail.asp?prod=SC36A
    https://www.ssfirearms.com/proddetail.asp?prod=SC36B
    https://www.ssfirearms.com/proddetail.asp?prod=SC36C
    Last edited by Maillemaker; 09-27-2022 at 07:14 PM.
    Steve Sheldon
    Commander
    4th Louisiana Delta Rifles
    NRA Certified Muzzleloading Instructor

Similar Threads

  1. Replies: 1
    Last Post: 10-29-2021, 09:55 AM
  2. WANTED/Rear Sight Sighting Device for peep sight
    By Carl in forum Wanted/For Sale Items
    Replies: 3
    Last Post: 07-05-2012, 09:53 AM
  3. Sight drilling and improved front sight question.
    By gunhawk in forum Shooting Techs, Tips, & Tricks
    Replies: 5
    Last Post: 12-25-2011, 09:35 PM
  4. Help! I need advise with attaching a forearm stub
    By Timmeu in forum Shooting Techs, Tips, & Tricks
    Replies: 5
    Last Post: 03-30-2011, 11:34 AM
  5. Attaching Sabots
    By randell in forum Artillery
    Replies: 1
    Last Post: 06-04-2009, 07:56 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •