Results 1 to 8 of 8

Thread: Preventing wood erosion & scorching behind nipple on military rifle/musket?

  1. #1
    Koauk is offline
    Team:
    Visitor (non-N-SSA Member)
    Member
    NA
    Join Date
    Dec 2018
    Location
    California
    Posts
    3
    Region:
    Visitor

    Preventing wood erosion & scorching behind nipple on military rifle/musket?

    I've had my Pedersoli 1841 Mississippi rifle out a couple of times and have noticed that the wood just behind the nipple is scorched and the wood has very slightly eroded.

    Is there a way to prevent this? A flash cup won't fit.

  2. #2
    Join Date
    Aug 2011
    Posts
    64
    Region:
    Deep South - Georgia, Louisiana, Tennessee, Mississippi and Texas
    I've seen some guys use a small piece of aluminum duct tape to protect that area.

  3. #3
    Muley Gil is offline
    Team:
    34th Battalion Virginia Cavalry
    Member
    3020V
    Join Date
    May 2004
    Location
    Southwest Virginia
    Posts
    1,676
    Region:
    New England - New York, Connecticut, New Jersey and Massachusetts
    My daddy used to shoot a Navy Arms Zouave that a previous owner had inlaid a small brass plate in that area.
    Gil Davis Tercenio
    # 3020V
    34th Battalion, Virginia Cavalry
    Great, great grandson of Cpl Elijah S Davis, Co I, 6th Alabama Inf CSA

  4. #4
    John Holland is offline Moderator
    Team:
    44th NY Volunteer Infantry
    Member
    00973V
    Join Date
    Nov 2004
    Posts
    2,871
    Region:
    Northeast- New York
    The suggestions of covering the wood are positive fixes. In addition to that, perhaps a replacement nipple with a smaller flash hole will also help to improve the situation.

  5. #5
    Koauk is offline
    Team:
    Visitor (non-N-SSA Member)
    Member
    NA
    Join Date
    Dec 2018
    Location
    California
    Posts
    3
    Region:
    Visitor
    Thanks for the responses! I tried using a piece of leather that I tied on behind the nipple/bolster (suggested on another forum). It works just fine though I will need a new piece of leather each time as it eats away at it. Going to try a thicker piece of leather to see if it will take more abuse.

  6. #6
    MR. GADGET's Avatar
    MR. GADGET is offline Moderator
    Team:
    Rowan Artillery
    Member
    11873V
    Join Date
    Apr 2006
    Location
    Raleigh NC
    Posts
    1,518
    Region:
    Tidewater - Virginia and North Carolina
    One big thing is the wood. If the wood dry, no oil or finish it will burn fast. It you have added BLO to it and cured you will be a lot better off. If you oil it, that works also.

    An easy thing is to get the aluminum tape to add or get brass shim stock cut out and glue or tape with double sided tape like 3M auto tape. It is made to take heat, weather and so on.
    Most auto stores carry it.

    When you find the shape you want to use just make several add the tape, place in pill bottle and they will be ready to go if one comes off. Brass can be molded to fit really easy.
    MR. GADGET
    NRA LIFE BENEFACTOR MEMBER
    Rowan Artillery
    N-SSA National Provost Guard

    Just remember!
    When a pot needs stirring, someone needs to do it...

  7. #7
    efritz is offline
    Team:
    149th Pennsylvania Volunteer Infantry
    Member
    00701
    Join Date
    Aug 2004
    Posts
    436
    Region:
    Middle Atlantic - New York, Pennsylvania and New Jersey
    I’ve used black electrical tape behind and forward of the nipple for umteen years.
    When in doubt, mumble, when in trouble, delegate.

  8. #8
    Southron Sr. is offline
    Team:
    24th Georgia Volunteer Infantry
    Member
    3002
    Join Date
    Feb 2006
    Location
    Gorgia
    Posts
    1,319
    Region:
    Carolina - North Carolina and South Carolina

    No big deal...easily cured

    I have seen an original M1842 that had such bad "wood erosion" from the cap blast, you could see down into the lock's innards!

    Generally, IF YOU ARE GLASS BEDDING THE BREECH AREA... then a little bit of glass bedding behind the bolster fence will take care of the problem.

    A FAST AND EASY CURE. Take out a regular pair of house hold scissors and then cut out some aluminum from a beer or soft drink can you have lying around the house.

    Then simply bend and install this piece of aluminum to protect the wood behind the bolster fence. Usually the inside of soft drink cans are "brass colored" anyway. I would also cut out the aluminum "patch" big enough so it would held in place by the tang and lock plate when the barrel and lock are installed. The aluminum will protect your wood behind the bolster fence from "cap burn."

    This is a "zero cost" fix IF you have some empty beer or soft drink cans around your house...OR you can go out and buy a 6 pack or case of beer IF you need an excuse for doing the same!

Similar Threads

  1. Preventing voids in bullets, an experiment.
    By Maillemaker in forum Shooting Techs, Tips, & Tricks
    Replies: 28
    Last Post: 05-15-2019, 07:52 AM
  2. Looking for a Ballard Military rifle
    By Tim Lyne in forum Wanted/For Sale Items
    Replies: 5
    Last Post: 10-23-2013, 06:34 PM
  3. WTB Whitworth Military Target Rifle.
    By Jonah Hex in forum Wanted/For Sale Items
    Replies: 1
    Last Post: 05-24-2013, 01:52 PM
  4. WTB Platinum Lined Musket Nipple for EA Volunteer Rifle
    By oscarlovel in forum Wanted/For Sale Items
    Replies: 5
    Last Post: 01-14-2012, 05:21 PM
  5. Rifle Shoppe German/Hessian Military Jaeger Rifle for sale
    By Jim Chochole in forum Wanted/For Sale Items
    Replies: 1
    Last Post: 03-01-2009, 10:56 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •