Results 1 to 9 of 9

Thread: Smith bullet sizing

  1. #1
    Join Date
    Aug 2011
    Location
    Crossville. Tennessee
    Posts
    26
    Region:
    New England - New York, Connecticut, New Jersey and Massachusetts

    Smith bullet sizing

    Bought an original Smith reclined by Bob and it slugs out at .510". Ordered a Moose .515-385 mould. What diameter should I size the bullet to for best results? I have a .5135 diameter sizing die in my Saeco lubris.izee

  2. #2
    Lou Lou Lou is offline
    Team:
    Tammany Regiment, 42nd New York
    Member
    4869
    Join Date
    May 2004
    Location
    Lung Island, New Yawk
    Posts
    1,965
    Region:
    New England - New York, Connecticut, New Jersey and Massachusetts
    Try it as cast first. It might surprise you
    Lou Lou Lou Ruggiero
    Tammany Regt-42nd NYVI

  3. #3
    Join Date
    Sep 2006
    Location
    Ormond Beach,Fl.
    Posts
    78
    Region:
    New England - New York, Connecticut, New Jersey and Massachusetts

    Sizer

    Quote Originally Posted by Lou Lou Lou View Post
    Try it as cast first. It might surprise you
    Try your69 Cal round ball you can make it fit

  4. #4
    RaiderANV's Avatar
    RaiderANV is offline
    Team:
    Palmetto Sharpshooters
    Member
    5795V
    Join Date
    Mar 2006
    Location
    Virginny & McKinney, Texas
    Posts
    2,472
    Region:
    Carolina - North Carolina and South Carolina
    That question is best asked of Bobby Hoyt who would know best.
    Never squat with yer spurs on!!!

    Pat "PJ" Kelly #5795V
    Virginny & Texas
    540-878-8024

    MAYNARDS RULE!! & starr's DROOL!
    Hence the rust. MAYNARDAE LAUS DEO!

  5. #5
    Join Date
    Feb 2016
    Location
    SE Georgia
    Posts
    636
    Region:
    Deep South - Georgia, Louisiana, Tennessee, Mississippi and Texas
    .002" over groove diameter is not a bad rule of thumb for breech loading guns.

  6. #6
    Join Date
    Aug 2011
    Location
    Crossville. Tennessee
    Posts
    26
    Region:
    New England - New York, Connecticut, New Jersey and Massachusetts

    sizing smith

    Thanks for your advice.Will try "as cast" and .513.

  7. #7
    Join Date
    Mar 2014
    Location
    Chesapeake VA
    Posts
    64
    Region:
    Tidewater - Virginia and North Carolina
    Bob,

    I have been struggling getting my Smith to group, with the help of a teammate I have found a .518 bullet is doing it for me.

    Wayne

  8. #8
    jonk is offline
    Team:
    Genl Wm T Sherman's Bodyguard
    Member
    12999
    Join Date
    Jun 2012
    Posts
    1,106
    Region:
    Midwest - Ohio, Kentucky and Indiana
    Surprised it's that tight.

    I also subscribe to 2/1000" over groove diameter. NOT bore diameter. Now, after that, you just have to play with loads, lead hardness, etc.

    Personally, I size at .516 for soft or .520 for hard. Bore groove diameter measures .517, and those are the sizers I have on hand. I get similar accuracy from both, but usually go the soft route, as it's cheaper than buying tin, and wheelweights are just too variable and have too much junk in them (zinc and the like) these days, for use in anything but smoothbore. Different molds, too I might add. The 520 I have also shoots fine if cast from pure lead, but is a single cavity, while the 516 is a 6 banger.

  9. #9
    ms3635v's Avatar
    ms3635v is offline
    Team:
    1st Pennsylvania Cavalry
    Member
    03635V
    Join Date
    Nov 2006
    Location
    suburban Philly
    Posts
    866
    Region:
    Middle Atlantic - New York, Pennsylvania and New Jersey
    I know, from speaking with Bob, that if you bring a sized bullet with the barrel you are having relined, he then can cut the rifling to the correct depth.
    Mike Santarelli 03635V, Adjutant
    Member since 1979
    Co. B, 1st Pennsylvania Cavalry, #229
    National Inspector General
    Small Arms Committee

Similar Threads

  1. Need .542 bullet sizing die
    By David Sulewski in forum Wanted/For Sale Items
    Replies: 3
    Last Post: 08-02-2013, 07:47 PM
  2. Sizing of Maynard Bullet
    By MikeArthur in forum Shooting Techs, Tips, & Tricks
    Replies: 2
    Last Post: 02-16-2013, 03:37 PM
  3. smith bullet sizing die
    By iron brigade in forum Wanted/For Sale Items
    Replies: 2
    Last Post: 03-27-2012, 06:37 PM
  4. wtb bullet sizing die
    By canoesolo in forum Wanted/For Sale Items
    Replies: 2
    Last Post: 11-22-2009, 01:05 AM
  5. Breach Loader Bullet Sizing
    By Scott Kurki, 12475 in forum Small Arms
    Replies: 1
    Last Post: 12-04-2008, 08:59 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •