Results 1 to 8 of 8

Thread: Removing broken off cleanout screw in Merrill Carbine

  1. #1
    Join Date
    Feb 2016
    Location
    SE Georgia
    Posts
    636
    Region:
    Deep South - Georgia, Louisiana, Tennessee, Mississippi and Texas

    Removing broken off cleanout screw in Merrill Carbine

    I bought a Merrill carbine at a show a few weeks ago. I did not notice when I bought it, but the cleanout screw in the bolster is broken off. What are my options as far as removing it? You gotta wonder why it broke. If it's in there so tight (Corroded?) that it broke upon removal I doubt anything like a left handed drill bit or 'easy out' would come close. Is this something a gunsmith could do for me? Do I need to find someone with an EDM? Drill it and tap for next size up? Leave it alone and don't worry about it, just clean as best you can when done shooting?

  2. #2
    RaiderANV's Avatar
    RaiderANV is offline
    Team:
    Palmetto Sharpshooters
    Member
    5795V
    Join Date
    Mar 2006
    Location
    Virginny & McKinney, Texas
    Posts
    2,472
    Region:
    Carolina - North Carolina and South Carolina
    Rarely does a torch and EASYout(dern auto-correct) fail. The heat will break it loose. Many reasons it could have snapped.... Rusted heavy.....bad metal/spot in that one screw, list goes on. If you shy away from doing it the Nationals is yer best bet.
    Last edited by RaiderANV; 01-05-2017 at 11:30 PM.
    Never squat with yer spurs on!!!

    Pat "PJ" Kelly #5795V
    Virginny & Texas
    540-878-8024

    MAYNARDS RULE!! & starr's DROOL!
    Hence the rust. MAYNARDAE LAUS DEO!

  3. #3
    Join Date
    Feb 2016
    Location
    SE Georgia
    Posts
    636
    Region:
    Deep South - Georgia, Louisiana, Tennessee, Mississippi and Texas
    Thanks Pat. I understand torch, but what is washout?

    I have had luck with bolts and pipe fittings by heating with a rose bud and just letting them naturally cool. Like you say, the heat breaks down whatever is binding it up. I've never tried it on anything so small, and then there's the fact there's nothing to grab a hold of, but maybe THEN a left hand drill would do it, or maybe a pick if it's loose enough.

  4. #4
    John Holland is offline Moderator
    Team:
    44th NY Volunteer Infantry
    Member
    00973V
    Join Date
    Nov 2004
    Posts
    2,871
    Region:
    Northeast- New York
    Personally, I would leave it alone.

  5. #5
    RaiderANV's Avatar
    RaiderANV is offline
    Team:
    Palmetto Sharpshooters
    Member
    5795V
    Join Date
    Mar 2006
    Location
    Virginny & McKinney, Texas
    Posts
    2,472
    Region:
    Carolina - North Carolina and South Carolina
    Quote Originally Posted by Hal View Post
    Thanks Pat. I understand torch, but what is washout? .
    I meant easyout. dern computer corrected to washout and I didn't look back.
    Never squat with yer spurs on!!!

    Pat "PJ" Kelly #5795V
    Virginny & Texas
    540-878-8024

    MAYNARDS RULE!! & starr's DROOL!
    Hence the rust. MAYNARDAE LAUS DEO!

  6. #6
    Join Date
    Feb 2016
    Location
    SE Georgia
    Posts
    636
    Region:
    Deep South - Georgia, Louisiana, Tennessee, Mississippi and Texas
    Thanks Pat. I may give that a try. Gotta look at it again and see if I think heat will hurt any patina on it. It's not really a collectors grade gun, but still.....

    John, glad to know that is a viable option. I was afraid stuff would begin to build up in there.

  7. #7
    Join Date
    Feb 2016
    Location
    SE Georgia
    Posts
    636
    Region:
    Deep South - Georgia, Louisiana, Tennessee, Mississippi and Texas
    I took the advice of others and decided to leave it well enough alone. I was told that screw is likely an oddball thread (30 TPI, I think it was), and if I got it out, I would have trouble finding one to put back in there. Thanks for asking.

  8. #8
    MR. GADGET's Avatar
    MR. GADGET is offline Moderator
    Team:
    Rowan Artillery
    Member
    11873V
    Join Date
    Apr 2006
    Location
    Raleigh NC
    Posts
    1,518
    Region:
    Tidewater - Virginia and North Carolina
    If you really want it out I would call Tom Crone and see about getting him to do it.
    He can drill it out, tap and make a new screw out of SS or carbon steel to replace it.

    I have had him do a bunch for me. He has made screws I looked and never found for 30 years.
    Turns out the screws for the parts were made to a differnt spec back in the 30's and 40's
    He pulled the old one cloned it. Also made a lot of custom stuff and gear.
    The guy is good. He sets up at nationals and some other shoots.
    MR. GADGET
    NRA LIFE BENEFACTOR MEMBER
    Rowan Artillery
    N-SSA National Provost Guard

    Just remember!
    When a pot needs stirring, someone needs to do it...

Similar Threads

  1. Smith Carbine - Burned out cleanout screw.
    By dfbowers in forum Small Arms
    Replies: 17
    Last Post: 06-17-2018, 12:55 PM
  2. Merrill Carbine
    By robesetz in forum Small Arms
    Replies: 6
    Last Post: 10-30-2014, 06:25 PM
  3. Merrill carbine stock
    By maynard6 in forum Wanted/For Sale Items
    Replies: 0
    Last Post: 11-30-2012, 03:43 PM
  4. merrill carbine help!
    By farrier86 in forum Small Arms
    Replies: 1
    Last Post: 08-14-2012, 02:48 PM
  5. Removing broken nipple
    By mwmoore10261 in forum Shooting Techs, Tips, & Tricks
    Replies: 1
    Last Post: 04-21-2010, 10:37 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •