Results 1 to 7 of 7

Thread: Smith Carbine Buller Diameter

  1. #1
    hobbler is online now
    Team:
    Visitor (non-N-SSA Member)
    Member
    NA
    Join Date
    Dec 2008
    Posts
    355
    Region:
    Visitor

    Smith Carbine Buller Diameter

    Is there a "standard" bullet diameter that is used in the Smith carbines?

  2. #2
    Lou Lou Lou is offline
    Team:
    Tammany Regiment, 42nd New York
    Member
    4869
    Join Date
    May 2004
    Location
    Lung Island, New Yawk
    Posts
    1,965
    Region:
    New England - New York, Connecticut, New Jersey and Massachusetts
    Yes .515. That being said some folks opt for a bigger bullet. I used to shoot a .520, 500 gr short nose bullet in my orig smith because part of the lands were missing and this bullet bridged the gap
    Lou Lou Lou Ruggiero
    Tammany Regt-42nd NYVI

  3. #3
    JimSmith is offline
    Team:
    149th NY Volunteer Infantry
    Member
    10832
    Join Date
    May 2004
    Location
    Ithaca, NY
    Posts
    64
    Region:
    Northeast- New York

    Smith Bullet

    You should cast a .518 bullet and push it through from breech to muzzle with a cleaning rod. Then mike it.

    Lou is correct about the .515 because you start with a .500 bore and .007 grooves plus .001 over. That assumes your barrel is not worn or made wrong.

    Mine was oversized until I had it relined.

    Jim Smith
    Jim Smith, 10832
    149thNYVI

  4. #4
    ms3635v's Avatar
    ms3635v is offline
    Team:
    1st Pennsylvania Cavalry
    Member
    03635V
    Join Date
    Nov 2006
    Location
    suburban Philly
    Posts
    866
    Region:
    Middle Atlantic - New York, Pennsylvania and New Jersey
    I am shooting an original Smith. I use a .520" Moose 400 grain bullet sized to .518". I use 28 grains of GOEX 3F and lubed with MCM. This combination is extremely accurate at both 50 and 100 yards.
    Mike Santarelli 03635V, Adjutant
    Member since 1979
    Co. B, 1st Pennsylvania Cavalry, #229
    National Inspector General
    Small Arms Committee

  5. #5
    jonk is offline
    Team:
    Genl Wm T Sherman's Bodyguard
    Member
    12999
    Join Date
    Jun 2012
    Posts
    1,106
    Region:
    Midwest - Ohio, Kentucky and Indiana
    I shoot a .515 Lee cast of soft lead and one .50 .060" fiber wad, lubed with spg, over 30 gr of 2f. I tried .518 and .520. Was able to work up good loads with all of them, but as the .515 is a 6 cavity that's the one I use most.

    I'm shooting a Pietta. Given the uneven number of lands/grooves it is hard to slug, but I get no leading and good accuracy with the .515 so that's fine by me.

  6. #6
    bobanderson is offline
    Team:
    1st Michigan Infantry
    Member
    12291
    Join Date
    Aug 2008
    Location
    Howell, MI
    Posts
    831
    Region:
    Northwest Territory - Michigan, Ohio and Indiana
    Quote Originally Posted by Harry Gaul View Post
    My lube is a combination of 8 ounces of beeswax, 8 ounces of neatsfoot oil and a bar on Neutrogeneo soap melted together. It works for me.
    Harry
    i love the "N" lube. Used it for years. I used to cool the mix to almost solid so it wouldn't separate as it cooled in my stick moulds. A friend told me to melt a few flakes of Ivory soap in the pot to prevent that.
    THAT works for me.
    Bob Anderson
    Ordnance Sergeant
    Company C, 1st Michigan Volunteer Infantry
    Small Arms Committee

    "I won't be wronged. I won't be insulted. I won't be laid a hand on.
    I don't do these things to other people, and I require the same from them."
    - John Wayne in "The Shootist", 1976

  7. #7
    Joe Plakis, 9575V is offline
    Team:
    149th Pennsylvania Volunteer Infantry
    Member
    09575v
    Join Date
    Nov 2005
    Location
    North Of Philadelphia
    Posts
    513
    Region:
    Middle Atlantic - New York, Pennsylvania and New Jersey
    Nothing about Civil War Black Powder is "Standard"...... There might be popular bullet types, but the sizes of Smith Bullets will range anywhere from .508 up to .525, those are the two extremes I have heard people using, and I know tons of people in between those to calibers. My suggestion is to slug your muzzle and breech diameters, because it is always good to know that the muzzle is smaller than the breech, because there are a handful of repops out there that are backwards, and are .510 at the breech and .518 at the muzzle.

    As for bullet types find what works best for you, although the 515139 sized down to .002 above muzzle diameter is a great place to start.
    Joe Plakis XXVIII
    Middle-Atlantic Region
    SAC
    9575V

    "Great leadership does not mean running away from reality. Sometimes the hard truths might just demoralize the company, but at other times sharing difficulties can inspire people to take action that will make the situation better." John Kotter

Similar Threads

  1. Sharps bullet diameter
    By jek279 in forum Small Arms
    Replies: 2
    Last Post: 03-29-2015, 07:56 AM
  2. Maynard bore diameter
    By Ben Nevlezer in forum Small Arms
    Replies: 12
    Last Post: 02-03-2015, 08:35 PM
  3. Bore Diameter
    By Tom in forum Small Arms
    Replies: 2
    Last Post: 01-04-2014, 08:58 AM
  4. FS: machine made hand sizer .514 diameter with punch $20
    By John S. in forum Wanted/For Sale Items
    Replies: 0
    Last Post: 03-14-2013, 06:07 PM
  5. Plug pins to measure true bore diameter?
    By threepdr in forum Small Arms
    Replies: 9
    Last Post: 05-08-2008, 06:14 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •