View Full Version : Sharps gas check removal issues
I have a Pedersoli Sharps that I got off of a fellow board member and skirmishing team mate. Each time I take out the sliding chamber sleeve gas check, it gets harder and harder to do. Right now I'm using a compressible rubber thingamabob he made up but it is not long for this world... it has a few cracks in it.
1. What is the proper tool, and where can I get one?
2. After each shoot I promptly remove the check... however that involves degreasing and beating on my cleaning rod with progressively heavier hammers. After cleaning and drying I always coat it in high pressure synthetic grease, but it is just binding up something fierce. Any suggestions?
3. What lubricant should I use in particular? I am going to try some bull plate sprue lube on it next... can't do any worse than what Iv'e been using.
Francis J. Miller Jr, 02601
09-03-2012, 09:58 PM
Contact Charlie Hahn, He can help you with your Sharp's issue.
Charlie Hahn
410-208-4736
Charlie Hahn
09-04-2012, 08:40 AM
Here is my web sight, charliestubes.com. There is some information that to ponder, please call with questions
Charlie Hahn
410-208-4736
ian45662
09-04-2012, 02:26 PM
I will tell you right now whatever may be wrong with your sharps Charlie can fix it. Mine runs like a champ all day and the sleeve comes out with no problems. He installed a solid block and split sleeve in the chamber so the "O" ring is protected from hot gases
Ron/The Old Reb
09-05-2012, 08:54 AM
I coat it with Antiseize, comes out easy every time. You can buy it at an auto parts store.
johnefelts
09-07-2012, 04:41 PM
I have a Pedersoli Sharps that I got off of a fellow board member and skirmishing team mate. Each time I take out the sliding chamber sleeve gas check, it gets harder and harder to do. Right now I'm using a compressible rubber thingamabob he made up but it is not long for this world... it has a few cracks in it.
1. What is the proper tool, and where can I get one?
2. After each shoot I promptly remove the check... however that involves degreasing and beating on my cleaning rod with progressively heavier hammers. After cleaning and drying I always coat it in high pressure synthetic grease, but it is just binding up something fierce. Any suggestions?
3. What lubricant should I use in particular? I am going to try some bull plate sprue lube on it next... can't do any worse than what Iv'e been using.
I have the Pedersoli removal tool I can send you for 25.00 bucks, I dont need it after Charlie Hahn fixed mine.
Runs.for.beer
09-07-2012, 06:33 PM
If the OP takes a pass, I am very interested in purchasing the tool.Thanks!
gemmer
09-08-2012, 08:16 AM
If the OP takes a pass, I am very interested in purchasing the tool.Thanks!
If you can't get that one, I have one available. Same Price
Duane
Runs.for.beer
09-08-2012, 02:14 PM
If you can't get that one, I have one available. Same Price
Duane
PM Sent . . .
I have the Pedersoli removal tool I can send you for 25.00 bucks, I dont need it after Charlie Hahn fixed mine.
I think I can do that. PM sent.
For those interested, I tried the Bullplate sprue cutter lube. Just like on the molds, a drop is more than enough; no more stuck chamber sleeve. In fact it popped right out with a bent over screwdriver, requiring no pounding.
I never found the need to use the stuff on my mold sprue cutters personally, though I do on the alignment pins. Now another use for it... and the company is out of business so if you don't have it, that's that. The 3 bottles I have should last a lifetime even so.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.